Revision 3.XX requires that the IMPS.ini file reside in the same directory as IMPS.exe. Revision 2.XX and above use the revision 7.1 compiler. Revision 1.XX used the 6.1 compiler. Revision 1.XX software cannot be upgraded to 2.XX or above. A full install is required. Revision 3.10 The maximum number of votes was increased to 128. An extranious indicator was removed from the bar graph. Revision 3.09 The alarm window now appears near the top left corner of the display. The delay between alarm messages was increased from five to ten seconds. The Operator switch and Debug button are disabled until the program has initialized. Revision 3.08 The function that creates JPEG screen captures now saves the files to the chosen data directory, not the default. The ability to use future rev. B Sensors was added . Revision 3.07 The text for the Screen Capture Tip Strips were fixed. The bug in which the data shifted the wrong way in the bargrapgh when the x axis ended with 0 and dewander was enable was fixed. Revision 3.06 The High Alarm data range is 11-255. The High Warning data range is 10-254. The Low Warning data range is 1-240. The Low Alarm data range is 0-239. The "Alarm Enabled" control was added. Revision 3.05 A bug that corrupted the multi-deck graph colors was fixed. Enhancements were programmed in all the graphs and charts to make product changes more reliable. The Readback button is disabled unless a card is installed. "Valid Deck" was changed to "Average" on the Bar Graph. Changes in the Product screen are immediately available to the rest of the program. Revision 3.04 A compiler bug was fixed. A bug where the Setup screen always thought changes were made was fixed. Revision 3.03 Some start up bugs were fixed. Revision 3.02 Translations were added to the I/O Read back function. The Deck ID indicator was added to the I/O Read back function. The analog deck output was added. It AO.1 The equation is Vout = Deck*10/(# of decks). Revision 3.01 The I/O Readback function no longer creates a file. The I/O Readback button in the debug screen is disabled if there is no I/O car installed. The Setup funtion now checks if anything in the "Communucations" group is changed. Revision 3.00 The "Data" and "CSV Dir" directories can now be located anywhere on the local drive or on a network. One change is that "IMPS.INI" must now be located in the directory with "IMPS.EXE". The readback function is now accessed via a button on the Debug screen. The Multiplexer.CSV file now always contains enough data for 128 sensors. The Calibrate, Products, and Setup buttons are disabled until teh program is initialized. Revision 2.04 The readback function was modifies so that it is better synchronize with the analog output The Calibrate, Setup, and Product buttons are disabled until the program is completely initialized. Sometimes pressing one of these buttons too quickly upon startup causes problems. Revision 2.03 The Calibrate screen only shows data for the sensos that are installed. If new sensors are added, their data will appear automatically. Revision 2.02 The automatically starting readback function was disabled. Revision 2.01 Sensor direction indicators were added to the Multi-Deck graph. Revision 2.00 I/O card support was added. A readback function was added. It reads the I/O signals from a specially wired the interface card back to the IMPS program. Revision 1.34 Some problems with the Multi Deck graph x-axis display were fixed. The Multiplexer Selection control in the Calibrate screen is now initialized to multiplexer 1. Revision 1.33 The Chart Length Control in the Trend Chart was mistranslated. The Sensor Map was initialized to 127 columns. This was changed to 255 columns. Revision 1.32 A bug that caused screen reinitializations in the Cross Reference Graph when the Setup screen was open was fixed. Revision 1.31 Some controls in the Trend Chart and the Cross Reference Graph that should have been invisible were hidden. The default language was set to English. Revision 1.18.3 The software now supports boards longer than 255 samples. Revision 1.18.2 The Default Local IP Address was changed to 192.168.98.220. The Default Remote IP Address was changed to 192.168.98.222. The wiring and software manuals are now included in the installation. Revision 1.30 More Spanish support was added. A control to linearize the sensor output was added. Revision 1.29 Spanish language support was added. Revision 1.28 The High and Low Warning Levels were added. These levels are shown on the bar graph, the Deck Dross Section Graph, and the 3D Contour Graph. The moisture warning and alarm levels are now adjusted on the Setup screen. A control was added for the number of sensors required to trigger a moisture alarm or warning are required. A control was added for the type of analysis, average of real time.s Dialog boxes were added to display high and low alarms and warnings. A memory leak in the Calibrate Sensors program was fixed. Revision 1.27 Many buttons were changed to icons. The printscreen functions were added to the graphing programs. The Deck Cross Section graph was added. Revision 1.18.1 The Program now supports up to 128 real and 127 virtual ports. Revision 1.26 An initialization problem in the Bar Graph was fixed. A problem where the Product page would overrule the product code selection in another screen was fixed. A program to split a csv file into many files of a selected number of rows was added. Revision 1.25 There is now a warning when a board exceeds the maximum size. Revision 1.24 The moisture axis maximum and minimums were moved from the graphs to the setup screen. Now these axis on the Bar Graph, 3D Contour Graph, and Trend Chart will be equal. Revision 1.23 The maximum number of reference samples was increased from 20 to 100. Upon exiting, the Calibrate, Product Table, and Setup screens now give warnings if a control is changed and is different than the IMPS.INI file. The limit lines and x axis on the Bar Graph now draw properly if there is no data. In the Calibrate screen, the control disabling/enabling for operator/administrator mode was enhanced. Revision 1.22 Some problems with the X axis on the MultiDeck Graph were fixed. The individual Reference buttons were returned. Revision 1.21 The Bar Graph, Multi_Deck Graph, 2D Contour Graph, and 3D Contour Graph each have their own Sensor axis direction controls. Revision 1.20 The individual reference buttons were removed. Now one reference button references the whole mux. The Auto zero values are saved every 30 minutes. Revision 1.19 A bug calculating the moisture zeros was fixed. The graph buttons were changed and moved to the bottom of the graphs Revision 1.18 A Trend Chart startup damping error was fixed. The overall average is now read from the log file. The 3D graph uses less system resources than before. Revision 1.17 The scroll bar was added to the Trend Chart. The Update Enable Indicator was added to the Trend Chart. The overall average was added to the log file. Revision 1.15 The auto zero delay was fixed. The deck, product code, and product description were added to the log file. At startup the program reads the log file. During operation it adds new values. These are stored in the main program so the Trend Chart always has a history. Revision 1.14 The auto zero values are shown in the Calibration screen. The auto zero delay is set to 0 when the maximum board length was reached. The Zero and Master Zero buttons now work with the auto zero. The moisture calculation was fixed to work with many negative numbers.